Posiadam kartę sieciową w laptopie (ath5k, mini pci-e), lecz chciałbym ją zastąpić kartą sieciową na USB. Kupiłem takie cudo 'Opticum gxu-301'. Nie znalazłem w sieci co to jest, więc skonfigurowałem jądro na wszystkie karty sieciowe jako modemy.
Coś się znalazło:
Kod: Zaznacz cały
san@eeepc:~$ lsmod
Module Size Used by
ath5k 101890 0
ath 5882 1 ath5k
rt2800usb 25111 0
rt2x00usb 5211 1 rt2800usb
rt2x00lib 19321 2 rt2800usb,rt2x00usb
mac80211 99278 3 ath5k,rt2x00usb,rt2x00lib
sg 12864 0
cfg80211 85480 4 ath5k,ath,rt2x00lib,mac80211
eeepc_laptop 9221 0
rfkill 6628 3 cfg80211,eeepc_laptop
Kod: Zaznacz cały
[ 719.106063] usb 1-3: new high speed USB device using ehci_hcd and address 7
[ 719.240672] usb 1-3: configuration #1 chosen from 1 choice
[ 719.284177] phy3 -> rt2x00_set_chip: Info - Chipset detected - rt: 1600, rf: 0006, rev: 30700200.
[ 719.298705] phy3: Selected rate control algorithm 'minstrel'
[ 719.319116] Registered led device: rt2800usb-phy3::radio
[ 719.325561] Registered led device: rt2800usb-phy3::assoc
[ 719.333101] Registered led device: rt2800usb-phy3::quality
[ 719.366472] udev: renamed network interface wlan0 to wlan2
[ 719.380729] phy3 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'.
[ 719.380741] rt2800usb 1-3:1.0: firmware: requesting rt2870.bin
[ 719.400489] phy3 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8.
[ 719.628063] phy3 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[ 719.631538] phy3 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[ 719.633157] phy3 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[ 719.635410] phy3 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
Kod: Zaznacz cały
san@eeepc:~$ iwlist scan
lo Interface doesn't support scanning.
wlan1 Scan completed :
Cell 01 - Address: 00:02:72:5C:91:7F
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=44/70 Signal level=-66 dBm
Encryption key:on
ESSID:"Ratamahatta"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=0000085779091593
Extra: Last beacon: 53441ms ago
IE: Unknown: 000B526174616D616861747461
IE: Unknown: 010882848B960C121824
IE: Unknown: 030101
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
wlan2 No scan results
Próbowałem dodać moduły ath i ath5k do blacklisty, bo wyłączanie jej przez ACPI wywoływało dziwne reakcje - nic z tego.
No i trochę zgłupiałem... Nie wiem czego próbować.
Pozdrawiam!